myNABCO

Surface-Mounted Operator: Side Load – Surface Mounted

Literature

Select a product

Literature Type

  • All
    • All
    • Specifications
    • Architectural Drawings
    • Product Manuals
    • Archived Manuals
    • Technical Bulletins
    • Technical Newsletter
  • Specifications
    • GT400 & 8400 Swing Operator Conversion Unit (Specifications) pdf | docx |
  • Architectural Drawings
    • Mounting Operator to Metal Door & Frame Architectural Drawing pdf | dwg |
    • Sideload Header – Left Hand Inswing (GT8400-01L) pdf | dwg |
    • Sideload Header – Left Hand Inswing With Panic – Center Pivot (GT8400-01LP) pdf | dwg |
    • Sideload Header – Right Hand Inswing (GT8400-01R) pdf | dwg |
    • Sideload Header – Right Hand Inswing With Panic – Center Pivot (GT8400-01RP) pdf | dwg |
    • Sideload Header – Left Hand Outswing (GT8400-02L) pdf | dwg |
    • Sideload Header – Right Hand Outswing (GT8400-02R) pdf | dwg |
    • Sideload Header – Simultaneous Pair Inswing (GT8400-03) pdf | dwg |
    • Sideload Header – Simultaneous Pair Inswing W/Panic – Center Pivot (GT8400-03P) pdf | dwg |
    • Sideload Header – Simultaneous Pair Outswing (GT8400-04) pdf | dwg |
    • Sideload Header – Dual Inswing/Outswing (GT8400-05) pdf | dwg |
    • Sideload Header – Center Pivot – Dual Inswing/Outswing With Panic (GT8400-05P) pdf | dwg |
    • Sideload Header – Double Egress Pair (GT8400-06) pdf | dwg |
  • Product Manuals
  • Archived Manuals
    • C-00185 OPUS Retrofit Kit Installation Manual Rev 4-23-18 |
    • C-00139 Opus Control Wiring and Programming Installation Manual, Rev 10-23-18 |
    • C-00139 Opus Control Installation Manual, Rev 3-30-17 |
    • C-00169 Wiring and Programming Manual, OPUS control, rev 6-13-16 |
    • C-00185 Quick Setup & Parts Guide, Opus Retrofit Kit, rev 6-13-16 |
    • C-00174 Quick Setup & Parts Guide GT(8)400-(8)500-(8)600 CU Swing Door Operator, Rev 8-10-16 |
    • C-00185 OPUS Retrofit Kit Installation Manual Rev 9-22-16 |
    • C-00174 Hardware Installation Manual Opus 400-500-600 8400-8500-8600 Rev 3-22-17 |
    • C-00139 Quick Setup & Parts Guide – Opus Control, Rev 6-13-16 |
    • C-00092 – Quick Setup & Parts Guide – GT(8)400-(8)500-(8)600 CU Magnum Swing Door Operator, Rev 8-10-16 |
    • C-00185 Opus Retro Manual Rev 4-8-20 |
    • C-00324 2 Pos KeySwitch Rev 3-14-18 |
    • C-00334 4 PosKeySwtch Rev 3-15-18 |
    • C-00139 Opus Control Wiring and Programming Installation Manual, Rev 5-16-19 |
    • C-00185 Opus Retro Manual Rev 10-3-19 |
    • C-00139 Opus Control Wire and Programming |
    • C-00174 Hardware Installation Manual Opus 400-500-600 8400-8500 Rev 6-29-18 |
    • C-00139 Opus Control Installation Manual, Rev 11-4-16 |
    • Service Parts – GT400 Single CU Analog Control – 2012 and earlier (note not all parts many be available) |
    • C-00174 Hardware Installation Manual Opus 400-500-600 8400-8500 Rev 1-21-19 |
    • 15-14985 Hardware Installation Manual GT(8)400,(8)500,(8)600 CU with Opus Controls Rev 5-26-16 |
    • 10-2207 Time-Delay-Model-2200 for Analog Control Rev 06-22-00 |
    • 14-2182 Soft-Start-Harness-Instructions, for Analog Control Rev 1-1-02 |
    • 15-10538 Installation Manual GT8400/8500 Swing Door Operator, Rev-9-26-14 |
  • Technical Bulletins
    • Technical Bulletin 91 Display Issues on Opus Controls |
    • Technical Bulletin 72 GT20 Inswing Units with Greater than 0” Reveal Require Two Piece Dog Leg Arm |
    • Technical Bulletin 99 Opus Instructional Videos |
    • Technical Bulletin 92 Input 62 Failure on Opus Controls |
    • Technical Bulletin 93 How to Change the Hand and/or Direction of Swing on a GT20 |
    • Technical Bulletin 71 Identifying and Preloading the New Reduced Opening Force (ROF) Operators |
    • Technical Bulletin 73 Use of Radio Receivers with the Opus Control |
    • Technical Bulletin 96 Software Issue on GT20 |
    • Technical Bulletin 100 Push & Go and Recycle on Swing Door Pairs with Opus |
    • Technical Bulletin 77 Opus Control Programming Tips |
    • Technical Bulletin 87 New & Rebuilt Analog, Magnum or U01-U19 controls no Longer Available |
    • Technical Bulletin 86 Sensor Monitoring Primer |
    • Technical Bulletin 101 Setting up Opus Controls on Swinger Pairs and Bi-Folds |
    • Technical Bulletin 89 Implementation of Sensor Monitoring in Production Units |
    • Technical Bulletin 80 Using “Push & Go” on GT20 |
    • Technical Bulletin 81 Opus Control Programming Tips Update |
    • Technical Bulletin 103 Hot Resistor on Swing Operators and Folding Door Systems |
    • Technical Bulletin 108 Changes to Swing Header Mounting Hardware |
    • Technical Bulletin 89A Update to Bulletin 89 on Sensor Monitoring Settings |
    • Technical Bulletin 68 Introducing the New Opus Control |
  • Technical Newsletter